Replacing a full HVAC system — furnace and central air together — costs $7,500 to $16,500 installed in 2026 for a typical 3-ton home system. High-efficiency equipment, heat pumps and ductwork changes push toward and past the top of the range.
For a typical full replacement: 3-ton central AC with a 80,000 BTU gas furnace, reusing sound ductwork.
| Cost item | What's included | Low end | High end |
|---|---|---|---|
| Outdoor AC / condensing unit | 3-ton condenser, standard efficiency (14.3–16 SEER2 class) | $2,200 | $4,500 |
| Furnace / air handler | 80,000 BTU gas furnace, 80–96% AFUE, blower and controls | $1,800 | $3,800 |
| Evaporator coil & line set | Indoor coil, refrigerant lines, condensate drain and pad | $600 | $1,400 |
| Installation labor | Removal of old equipment, setting, charging, startup and testing | $2,000 | $4,000 |
| Thermostat & controls | Programmable or smart thermostat, wiring and setup | $150 | $600 |
| Permits, disposal & inspection | Mechanical permit, refrigerant recovery, old unit haul-away | $300 | $900 |
| Ductwork modifications | Plenum adaptation, minor repairs and sealing (full re-ducting costs more) | $0 | $2,500 |
| Total (full system, 3-ton) | 2026 national estimate | $7,500 | $16,500 |
2026 national estimates for planning. Full ductwork replacement adds $3,000–$8,000. Federal tax credits and utility rebates for high-efficiency heat pumps can offset $1,000–$2,000+ — check current programs before you buy.
| System | Best for | Typical low | Typical high |
|---|---|---|---|
| Furnace only (gas) | Heating replacement, AC still serviceable | $3,800 | $7,500 |
| Central AC only | Cooling replacement, furnace still serviceable | $4,200 | $8,500 |
| Furnace + AC (matched) | Both units at end of life — the common case | $7,500 | $16,500 |
| Heat pump system | Heating and cooling in one unit; mild-to-moderate climates, or with backup heat | $8,500 | $18,000 |
| High-efficiency / variable speed | Lowest bills and best comfort, premium equipment | $12,000 | $22,000 |
| Ductless mini-split (multi-zone) | No existing ducts, additions, older homes | $6,000 | $16,000 |
DIY: Thermostat swaps, filter discipline and keeping the outdoor unit clear are yours. Actual system replacement is licensed work almost everywhere — refrigerant handling requires federal EPA certification, and gas and electrical connections require permits and inspections.
Hire a pro for: the replacement itself. Choose a contractor who performs a load calculation instead of quoting "same size as the old one," and get the equipment model numbers in writing so you can compare quotes apples-to-apples.
Furnaces typically last 15–25 years, central AC 12–17 years, heat pumps 12–15 years. Systems in hot climates with long cooling seasons wear faster.
A common rule: if the repair costs more than about a third of replacement and the system is past 12 years old, replacement usually wins. Frequent repairs, rising bills and refrigerant type (older R-22 systems) also tip the scale.
Typically 3 to 3.5 tons of cooling, but insulation, windows, ceiling height and climate matter as much as square footage. Insist on a load calculation rather than a rule of thumb.
Modern cold-climate heat pumps work efficiently well below freezing and are increasingly common in the Northeast and Midwest, usually with backup heat for the coldest days. Rebates and tax credits can be substantial — verify the current programs in your state.
A straightforward like-for-like swap is usually one day. Add a day or two for ductwork changes, fuel conversions or electrical panel work.